Construction safety quiz
This free safety quiz has 20 multiple-choice questions on falls, ladders, scaffolds, electrical, trenching, PPE, hazard communication, and heat and cold. Every answer shows the OSHA rule it comes from, quoted word for word. Take it on your phone, or print it for a tailgate meeting with an answer key and a sign-off sheet.
The crew copy has the 20 questions and a sign-off sheet. The leader copy adds the answer key with the OSHA rule for each answer. Nothing you pick leaves your browser.
Construction Safety Quiz
20 questions from OSHA rules. Circle one answer for each question. tailgatedocs.com/tools/safety-quiz
Date: ______________________
Job or site: ________________
Led by: ____________________
1. On a construction site, a worker stands near an open side or edge. At what height above the lower level does OSHA require fall protection?
A. 4 feet
B. 6 feet
C. 10 feet
D. 15 feet
2. How high must the top rail of a guardrail sit above the walking or working level?
A. 36 inches, give or take 2 inches
B. 39 inches or more, with no upper limit
C. 42 inches, plus or minus 3 inches
D. 48 inches, plus or minus 6 inches
3. A plywood cover sits over a hole in a floor or roof (not in a road or vehicle aisle). How much weight must it hold?
A. The weight of one worker
B. At least 200 pounds
C. Whatever the plywood is rated for
D. Twice the combined weight of the people, tools and materials that could be on it at once, or more
4. No qualified person has designed it into a complete system. How much must an anchor for a personal fall arrest system hold?
A. 1,800 pounds per worker
B. 3,000 pounds per worker
C. 4,000 pounds per worker
D. 5,000 pounds per worker attached
5. A portable ladder is used to get up onto a roof or upper landing. How far must its side rails reach above the landing?
A. 1 foot
B. 18 inches
C. 2 feet
D. 3 feet
6. An extension ladder leans on a wall. How far out from the top support should its foot be?
A. About one quarter of the working length
B. About one half of the working length
C. About one eighth of the working length
D. Always 3 feet, whatever the length
7. Above what height must a worker on a scaffold be protected from falling?
A. More than 4 feet
B. More than 6 feet
C. More than 10 feet
D. More than 20 feet
8. When must a competent person inspect a scaffold for visible defects?
A. Before each work shift, and after anything that could affect its structure
B. Once a week
C. Only when it is first put up
D. Once a month, with a written tag
9. Your site uses GFCIs to protect workers from shock. Which outlets in use need one?
A. Only outlets used outdoors
B. Only 240-volt outlets
C. All 120-volt, single-phase, 15- and 20-amp outlets that are not part of the building's permanent wiring
D. None, as long as the cords are heavy duty
10. OSHA's crane rule lists a minimum clearance from power lines by voltage. For a line up to 50 kV, what is it?
A. 10 feet
B. 15 feet
C. 20 feet
D. 25 feet
11. Unless a trench is dug entirely in stable rock, at what depth does OSHA require a protective system (sloping, shoring or a shield)?
A. 3 feet
B. 5 feet
C. 8 feet
D. 20 feet
12. A trench is 4 feet deep or more. How far may a worker have to walk along it to reach a ladder, ramp or other way out?
A. No more than 25 feet
B. No more than 50 feet
C. No more than 100 feet
D. There is no limit
13. Who inspects an excavation, and when?
A. The machine operator, at the end of each shift
B. An OSHA inspector, once a week
C. Any crew member, once a week
D. A competent person, daily before work starts, as needed during the shift, and after every rainstorm
14. Who pays for the protective equipment OSHA requires on a construction job?
A. The worker
B. The employer, at no cost to workers, with a few exceptions
C. The general contractor, for every trade on site
D. The worker and the employer split the cost
15. How many numbered sections does a safety data sheet (SDS) have?
A. 8
B. 10
C. 12
D. 16
16. When must workers be able to get to the safety data sheets for the chemicals they use?
A. Only on request, within 5 days
B. During each work shift, while they are in their work area
C. Only during the yearly safety audit
D. Only after an exposure
17. In hot weather, how much water does OSHA's heat guide encourage workers to drink?
A. About 1 cup every 15 to 20 minutes (1 liter an hour)
B. About 1 cup an hour
C. Only at breaks and lunch
D. As much as possible, with no upper limit
18. A new worker starts in hot weather. What does OSHA's 20% rule say about day one?
A. A full shift in the heat from day one
B. Half the shift in the heat on day one
C. Start with 20% of the exposure on day one and add no more than 20% each day after
D. No work in the heat for the first two weeks
19. Hypothermia sets in when normal body temperature (98.6°F) drops below what?
A. 97°F
B. 95°F
C. 90°F
D. 85°F
20. A worker has frostbite on their fingers. Which of these should you NOT do?
A. Get medical help
B. Move them somewhere warm
C. Rub or massage the frozen area
D. Replace wet gloves with dry ones
Safety quiz sign-off
We took this quiz at the tailgate meeting and went over the answers together.
| # | Printed name | Signature | Score (of 20) |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 | |||
| 4 | |||
| 5 | |||
| 6 | |||
| 7 | |||
| 8 | |||
| 9 | |||
| 10 | |||
| 11 | |||
| 12 | |||
| 13 | |||
| 14 | |||
| 15 |
Meeting leader: ______________
Signature: __________________
Date: ______________________
Questions quote federal OSHA rules and OSHA publications as read on 16 Nov 2026. State-plan states may have stricter rules. Printed from tailgatedocs.com.
Safety quiz questions and answers: the OSHA numbers
The rule behind each question, in quiz order. Crews that know these numbers can spot a problem before someone gets hurt.
| # | Topic | What the rule says | Source |
|---|---|---|---|
| 1 | Falls | At 6 feet or more above a lower level, the worker needs guardrails, a safety net or a personal fall arrest system. | 29 CFR 1926.501(b)(1) |
| 2 | Falls | The top edge of the top rail sits 42 inches above the walking level, and it may be 3 inches higher or lower. | 29 CFR 1926.502(b)(1) |
| 3 | Falls | The cover must hold at least twice the load that could be on it at once: people, tools and materials together. | 29 CFR 1926.502(i)(2) |
| 4 | Falls | Each anchor must hold at least 5,000 pounds for every worker tied off to it. | 29 CFR 1926.502(d)(15) |
| 5 | Ladders | The rails go at least 3 feet above the landing so the climber has something to hold when stepping on and off. | 29 CFR 1926.1053(b)(1) |
| 6 | Ladders | The foot goes out about one quarter of the working length, the length along the ladder from the foot to the top support. | 29 CFR 1926.1053(b)(5)(i) |
| 7 | Scaffolds | Scaffolds have their own trigger height: more than 10 feet above a lower level. | 29 CFR 1926.451(g)(1) |
| 8 | Scaffolds | A competent person looks the scaffold over before every shift. | 29 CFR 1926.451(f)(3) |
| 9 | Electrical | Every temporary 120-volt, single-phase, 15- or 20-amp outlet that workers use needs a GFCI. | 29 CFR 1926.404(b)(1)(i)-(ii) |
| 10 | Electrical | For lines up to 50 kV the table sets 10 feet. | 29 CFR 1926.1408, Table A |
| 11 | Trenching | At 5 feet and deeper, workers need a protective system against cave-ins. | 29 CFR 1926.652(a)(1) |
| 12 | Trenching | Place a ladder, stairway, ramp or other safe way out so nobody walks more than 25 feet sideways to reach it. | 29 CFR 1926.651(c)(2) |
| 13 | Trenching | A competent person checks the excavation, the area next to it and the protective system every day before work starts. | 29 CFR 1926.651(k)(1) |
| 14 | PPE | Required PPE is the employer's cost, not the worker's. | 29 CFR 1926.95(d)(1)-(2) |
| 15 | Hazard communication | An SDS has 16 sections in a set order, from Section 1, Identification, to Section 16, Other information. | 29 CFR 1910.1200(g)(2) |
| 16 | Hazard communication | SDSs must be readily accessible during every shift. | 29 CFR 1910.1200(g)(8) |
| 17 | Heat and cold | OSHA encourages about 1 liter an hour, which is about 1 cup every 15 to 20 minutes. | OSHA 3743, Protecting Workers from the Effects of Heat |
| 18 | Heat and cold | New and returning workers build up slowly: 20% of the exposure on the first day, then no more than 20% more each day. | OSHA 3743, Protecting Workers from the Effects of Heat |
| 19 | Heat and cold | Hypothermia means body temperature has dropped below 95°F. | OSHA, Winter Weather: Cold Stress |
| 20 | Heat and cold | Do not rub or massage frostbitten skin. | OSHA, Winter Weather: Cold Stress |
How the safety quiz works
Pick one answer for each question. The quiz marks it right away, shows the correct letter, explains it in plain words, and quotes the exact sentence from the OSHA rule or OSHA guide it comes from. A link takes you to the free toolbox talk on the same topic.
When all 20 are answered, you get a score and a count by topic, so you can see where the crew is strong and where it needs another talk. Press “Take the quiz again” to clear it for the next person.
The questions come from federal OSHA construction rules in 29 CFR 1926, the hazard communication rule in 29 CFR 1910.1200 (which construction uses through 1926.59), the OSHA heat guide (OSHA 3743) and OSHA's cold stress page. We read each one on 16 November 2026 and quote the wording as it stands.
Using the quiz at a tailgate meeting
Print the crew copy, one per person. It has the 20 questions on one or two pages and a sign-off sheet with room for 15 names, signatures and scores. Print one leader copy with the answer key, which lists the right letter, a short reason and the rule for each question.
Give the crew about 10 minutes. Then go through the key out loud and spend your time on the questions most people got wrong. The leader signs and dates the bottom of the sheet. If you also take attendance, the free toolbox talk sign-in sheet generator makes a matching sheet in a few seconds.
Short on time? Pick one topic, such as trenching or ladders, read those questions out, and follow up with the ladder safety toolbox talk or the talk linked under the question. For the ladder angle question, the ladder angle calculator shows the base distance for any height.
Common questions
▸What questions are on a construction safety quiz?
This one has 20 questions on the hazards that hurt the most people on site: falls, ladders, scaffolds, electrical, trenching, PPE, hazard communication, and heat and cold. Each question asks for a number or a duty that comes straight from an OSHA rule, such as the 6-foot fall protection height or the 5-foot trench depth.
▸Does this safety quiz have an answer key?
Yes. On screen you see the right answer, the rule behind it and the exact OSHA wording as soon as you pick. To print, choose "Print with the answer key" for the leader copy, or "Print the quiz for the crew" for a copy without answers.
▸How do I run a safety quiz at a toolbox talk?
Hand out the crew copy, give people about 10 minutes, then read the answers out from the key and talk through the ones most people missed. Have everyone write their score on the sign-off sheet and sign it. Keep the sheet with your other meeting records.
▸Does a quiz count as OSHA training?
No. A quiz checks what people remember. It does not replace the training a rule requires, such as the fall protection training program in 29 CFR 1926.503(a)(1). It is a good way to find the topics a crew needs to hear about again.
▸At what height is fall protection required in construction?
At 6 feet or more above a lower level, under 29 CFR 1926.501(b)(1). Scaffolds use more than 10 feet (29 CFR 1926.451(g)(1)). Questions 1 and 7 of the quiz cover both.
▸Can I use this quiz in a state-plan state like California?
Yes, as a federal OSHA quiz. State-plan states run their own rules, and some numbers differ or are stricter. If you work under a state plan, check the questions against your state rules before you use the answer key.
Sources
- OSHA 29 CFR 1926.501, Duty to have fall protection: osha.gov/laws-regs/regulations/standardnumber/1926/1926.501
- OSHA 29 CFR 1926.502, rules for fall protection systems: osha.gov/laws-regs/regulations/standardnumber/1926/1926.502
- OSHA 29 CFR 1926.1053, Ladders: osha.gov/laws-regs/regulations/standardnumber/1926/1926.1053
- OSHA 29 CFR 1926.451, Scaffolds, general requirements: osha.gov/laws-regs/regulations/standardnumber/1926/1926.451
- OSHA 29 CFR 1926.404, Wiring design and protection: osha.gov/laws-regs/regulations/standardnumber/1926/1926.404
- OSHA 29 CFR 1926.1408, Power line safety (cranes), Table A: osha.gov/laws-regs/regulations/standardnumber/1926/1926.1408
- OSHA 29 CFR 1926.651 and 1926.652, Excavations: osha.gov/laws-regs/regulations/standardnumber/1926/1926.651 and 1926.652
- OSHA 29 CFR 1926.95, Criteria for personal protective equipment: osha.gov/laws-regs/regulations/standardnumber/1926/1926.95
- OSHA 29 CFR 1910.1200, Hazard communication: osha.gov/laws-regs/regulations/standardnumber/1910/1910.1200
- OSHA 3743, Protecting Workers from the Effects of Heat: https://www.osha.gov/sites/default/files/publications/OSHA3743.pdf
- OSHA, Winter Weather: Cold Stress: https://www.osha.gov/winter-weather/cold-stress
- Rule text read on the eCFR, Title 29 (issue of 10 November 2026): https://www.ecfr.gov/current/title-29
Want a quiz for every weekly talk, not just this one? One page per talk, in English and Spanish: Crew Quiz Pack, $14 →
All free safety toolsToolbox talk sign-in sheetFall clearance calculatorFree toolbox talks library
More free safety tools
Forklift capacity calculator
Estimate a forklift's reduced capacity when the load center is longer than the one on its data plate.
Fire extinguisher inspection checklist
Tick the monthly checks for each extinguisher and print a 12-month inspection log.
Ladder inspection checklist
Check a stepladder, extension or fixed ladder against OSHA and print the record.
Forklift inspection checklist
Run the OSHA daily check for a gas, LPG, diesel or electric forklift and print the record.
Hot work permit
Answer the OSHA fire rules for welding and cutting, set the fire watch and print a permit to sign.
PPE hazard assessment
Build the written PPE hazard assessment certification OSHA 1910.132(d) requires, ready to print.