Forklift capacity calculator
This free forklift capacity calculator estimates how much a truck can lift when the load center is longer than the one on its data plate. It uses OSHA's field method: rated load center ÷ actual load center x rated capacity. The answer is an estimate. The truck's data plate and the maker's load chart always govern.
Your load
The data plate governs, not this calculator.
- • OSHA calls this an estimate that “will not produce exact load reduction figures.” Use the truck's data plate and the maker's load chart when you have them.
- • An attachment such as a sideshifter or clamp generally lowers capacity. Read the capacity on the plate for the truck with that attachment.
- • The ratio looks at the load center only. OSHA's stability appendix also names the height of the load, off-center loads, and the forces from braking, turning, lifting and tilting.
- • No plate, or a plate you cannot read? Do not run the truck until it is replaced.
Enter the plate capacity, the rated load center and your load's load center (or length) to get the reduced capacity. Nothing you type leaves your browser.
This calculator applies OSHA's field estimate for a longer load center (Powered Industrial Trucks eTool) and the rated capacity rule in 29 CFR 1910.178(o)(2). It is a planning aid, not legal advice, and it does not replace a competent person’s judgment on site.
State-plan states may set stricter requirements than the federal rule. Confirm against the standard that applies to your work before relying on a number here.
Before the first lift of the shift, run the free forklift inspection checklist. It includes a check that the capacity plate is in place and readable.
Forklift load capacity chart by load center
Approximate capacity, in pounds, for trucks rated at a 24-inch load center, worked out with the OSHA field method and rounded down. Use it to see how fast capacity drops, or enter your own numbers in the forklift capacity calculator above. Use your own truck's plate and load chart for the real limit.
| Plate capacity at 24 in | 24 in | 30 in | 36 in | 42 in | 48 in |
|---|---|---|---|---|---|
| 3,000 lb | 3,000 | 2,400 | 2,000 | 1,714 | 1,500 |
| 4,000 lb | 4,000 | 3,200 | 2,666 | 2,285 | 2,000 |
| 5,000 lb | 5,000 | 4,000 | 3,333 | 2,857 | 2,500 |
| 6,000 lb | 6,000 | 4,800 | 4,000 | 3,428 | 3,000 |
| 8,000 lb | 8,000 | 6,400 | 5,333 | 4,571 | 4,000 |
A 48-inch load center is a 96-inch even load. At that length the estimate gives half the plate capacity.
How the forklift derate calculation works
A forklift's capacity is always given as two numbers together: a weight and a load center, for example 5,000 lb at 24 inches. The load center is the distance from the front face of the forks to the middle of the load's weight. When the load sticks out farther, its weight acts on a longer lever, and the truck can tip forward with less weight on the forks.
Multiplying the plate capacity by the rated load center gives the rated load moment, the most turning force the truck is built for. The forklift capacity calculator keeps that number the same and solves for weight at your load center: rated load center ÷ actual load center x rated capacity. OSHA's eTool gives this as a field estimate for when the maker's instructions are not at hand. Its worked example is a 4,000 lb truck at 24 inches lifting a load with a 36-inch load center: 24 ÷ 36 x 4,000 = about 2,666 lb.
The tool never shows more than the plate capacity. A load center shorter than the rated one does not raise the limit, because 1910.178(o)(2) caps loads at the rated capacity. If you only know the load's length and its weight is spread evenly, pick “Even load” and enter the length: the load center is half of it. Add the load's weight to see if it is over or under the estimate.
To keep the load center short, OSHA advises loading as close to the front wheels as you can and turning a long box so it sits widthwise across the forks. Operator training covers vehicle capacity and stability, and the free forklift and telehandler safety toolbox talk is a quick refresher for the crew.
What OSHA requires on forklift capacity
- 29 CFR 1910.178(o)(2): “Only loads within the rated capacity of the truck shall be handled.”
- 29 CFR 1910.178(o)(1): only stable or safely arranged loads are handled, with caution on off-center loads that cannot be centered.
- 29 CFR 1910.178(a)(4): changes that affect capacity need the maker's prior written approval, and the capacity, operation and maintenance plates are changed to match.
- 29 CFR 1910.178(a)(5) and (a)(6): non-factory front-end attachments get marked on the truck, and all nameplates and markings stay in place and legible.
- 29 CFR 1910.178(l)(3)(i)(H) and (I): operator training covers vehicle capacity and vehicle stability.
Common questions
▸How do you calculate forklift capacity at a longer load center?
Divide the rated load center by the actual load center, then multiply by the rated capacity. OSHA's own example: a truck rated 5,000 lb at 24 inches carrying a load with a 28-inch load center gives 24 ÷ 28 x 5,000 = about 4,285 lb. OSHA says this field estimate is not exact and the truck maker is the source of more precise numbers.
▸What is the load center on a forklift?
It is the horizontal distance from the vertical face of the forks (or the attachment) to the line through the load's center of gravity. For an even box pushed back against the forks, that is half the box's length along the forks. A 48-inch even load has a 24-inch load center.
▸Why are most forklifts rated at a 24-inch load center?
OSHA's stability appendix says trucks with a capacity of 30,000 pounds or less are normally rated at a 24-inch load center. Bigger trucks are normally rated at 36 or 48 inches. Always read the load center printed on your own truck's data plate.
▸What does OSHA say about forklift capacity?
Under 29 CFR 1910.178(o)(2), a truck may only handle loads that are within its rated capacity. The user must keep all nameplates and markings in place and legible (1910.178(a)(6)), and operator training must cover vehicle capacity (1910.178(l)(3)(i)(H)).
▸Does an attachment reduce forklift capacity?
Usually, yes. OSHA's eTool says adding an attachment generally lowers capacity. For attachments that did not come from the factory, the user must ask for the truck to be marked with the attachment and the approximate weight of the truck and attachment (1910.178(a)(5)). Changes that affect capacity need the maker's written approval first, and the capacity plate is changed to match (1910.178(a)(4)).
▸What is a forklift load moment?
The load moment is the load's weight times its load center. A truck rated 3,000 lb at 24 inches has a load moment of 72,000 inch-pounds. To find the most a longer load can weigh, divide 72,000 by its load center: at 30 inches that is 2,400 lb. This forklift capacity calculator shows the rated load moment with every result.
Sources
- OSHA eTool, Powered Industrial Trucks, Load Handling: Load Composition (field calculation, load moment, worked examples): https://www.osha.gov/etools/powered-industrial-trucks/load-handling/load-composition
- OSHA eTool, Powered Industrial Trucks, Nameplate (attachments, missing or illegible plates): https://www.osha.gov/etools/powered-industrial-trucks/types-fundamentals/parts/name-plate
- OSHA 29 CFR 1910.178, Powered industrial trucks, paragraphs (a)(4) to (a)(6), (l)(3) and (o): https://www.osha.gov/laws-regs/regulations/standardnumber/1910/1910.178 (also on the eCFR: https://www.ecfr.gov/current/title-29/section-1910.178)
- OSHA 29 CFR 1910.178 Appendix A, Stability of Powered Industrial Trucks (non-mandatory), A-1 and A-5.2: https://www.osha.gov/laws-regs/regulations/standardnumber/1910/1910.178AppA
Forklift inspection checklistOSHA forklift inspection requirementsForklift operator evaluation formConstruction safety quizAll free safety tools
More free safety tools
Safety quiz
Take a 20-question construction safety quiz with the OSHA rule for every answer, or print it with a key and sign-off sheet.
Fire extinguisher inspection checklist
Tick the monthly checks for each extinguisher and print a 12-month inspection log.
Ladder inspection checklist
Check a stepladder, extension or fixed ladder against OSHA and print the record.
Forklift inspection checklist
Run the OSHA daily check for a gas, LPG, diesel or electric forklift and print the record.
Hot work permit
Answer the OSHA fire rules for welding and cutting, set the fire watch and print a permit to sign.
PPE hazard assessment
Build the written PPE hazard assessment certification OSHA 1910.132(d) requires, ready to print.