Job Hazard Analysis for Roofing Contractors
Task-by-task hazard breakdown, ready before the pre-job brief. Generated for roofing contractors in under 30 minutes, every citation checked against our 29 CFR standards table, $29 flat. Delivered as a print-ready PDF, editable Word (.docx) available.
1,200+ documents generated · 350+ contractors served · Spanish version +$19
When you need this document
The GC wants a JHA (or AHA / JSA) for your task before work starts, or your safety program requires one per activity.
A completed JHA is the record that your crew broke the task into steps, matched each hazard to a control, and briefed the work before starting. It is what a GC pre-task-plan requirement asks for at the gate, and what an OSHA inspector looks for after a near miss to see whether the hazard was foreseen and controlled.
What's inside
- ✓ Task breakdown into work steps
- ✓ Hazards identified for every step
- ✓ Controls and safe work practices per hazard
- ✓ Required PPE and equipment checks
- ✓ Applicable safety standards, cited to the code that governs your state
- ✓ Crew review and sign-off block
Written for roofing work, not a template
Every job hazard analysis we build for roofing contractors is written around the hazards roofing crews actually face: falls from roof edges and openings, ladder use, hot work / torches, heat exposure, material hoisting. Here is the substance that goes into it.
Real roofing jobs where a JHA matters
- ▸Tearing off and re-decking a two-story steep-slope shingle roof while a ground crew loads debris below and no perimeter guardrail is up yet.
- ▸Running a torch-applied modified-bitumen system on a low-slope commercial roof, with LP torches and hot kettles working next to roof drains and mechanical curbs.
- ▸Loading bundles of shingles onto the roof by ladder hoist while other trades pass through the drop zone below.
OSHA standards on the Roofing focus list
The JHA is generated against these real 29 CFR sections for roofing work, and every citation is validated against a verified standards table before delivery:
- §29 CFR 1926.501(b)(10): fall protection during roofing work on low-slope roofs, 6 feet or more above a lower level
- §29 CFR 1926.501(b)(11): fall protection on steep roofs, 6 feet or more above a lower level
- §29 CFR 1926.502: fall protection systems criteria (guardrails, PFAS, warning lines, safety monitors)
- §29 CFR 1926.503: fall protection training requirements
- §29 CFR 1926.1053: ladders
- §29 CFR 1926.451: scaffolds
- §29 CFR 1926.352: fire prevention during welding, cutting, and heating (LP torches, hot kettles, torch-applied membrane)
- §29 CFR 1926.350: gas welding and cutting (handling and securing LP and fuel-gas cylinders on the roof)
- §29 CFR 1910.1200: hazard communication (adhesives, solvents, hot asphalt)
- §OSH Act 5(a)(1) General Duty Clause: heat illness prevention
What roofing crews get cited for
The plan is written to close out the issues that draw citations in roofing work:
- ⚠Fall protection, general requirements (29 CFR 1926.501): unguarded roof edges, uncovered skylights and holes, and unanchored harnesses. This is OSHA's single most-cited construction standard, and roofing draws citations under it more than almost any other trade.
- ⚠Ladders (29 CFR 1926.1053): the roof-access ladder not extended 3 feet above the eave, or set at the wrong angle.
- ⚠Hazard communication (29 CFR 1910.1200): missing labels and safety data sheets for the adhesives, solvents, and hot asphalt kept on the roof and in the truck.
What a job hazard analysis costs everywhere else
Same document, three very different price tags and wait times.
| Safety consultant | Template sellers | TailgateDocs | |
|---|---|---|---|
| Price | $500 to $2500 | $99 to $500 | $49 |
| Turnaround | 1 to 2 weeks | hours of DIY editing | Under 30 minutes |
| Site-specific to your project | Yes | No, you fill in blanks | Yes |
| Real 29 CFR citations | Yes | Sometimes outdated | Yes, verified against 140+ sections |
| Spanish version for your crew | Rarely | Almost never | Yes, +$19 |
| Revisions when the GC asks | Billed hourly | You edit it yourself | Free within 24h |
Common questions
▸How fast can I get a job hazard analysis?
Under 30 minutes after you finish the questionnaire, and usually well inside that. It downloads in the browser and a copy lands in your email. If a document needs an extra compliance check it comes by email instead, and we tell you.
▸Does it cover the OSHA standards for roofing work?
Yes. Roofing documents are generated against a curated focus list including 1926.501(b)(10), 1926.501(b)(11), 1926.502 and more, and every citation is validated against a verified standards table before delivery.
▸What if the GC or prequal reviewer asks for changes?
Reply to your delivery email and we revise the document free, within 24 hours and as many times as it takes, until your GC or prequal reviewer accepts it.
▸Can I get the JHA in Word (.docx)?
Yes. The document downloads instantly as a print-ready PDF, and you can add the editable Word (.docx) version for $19 at checkout or after delivery, so you can adjust it yourself later.
Job Hazard Analysis for other trades
ElectricalHVAC / MechanicalGeneral ContractorLandscapingPlumbingConcrete / Masonry
Free JHA resources
Free blank JHA template (Word & PDF)Filled JHA examplesHow to write a JHAThe JHA format, explained
Other documents
Site-Specific Safety Plan for Roofing ($49)Written Safety Program for Roofing ($149)Heat Illness Prevention Plan for Roofing ($49)California Workplace Violence Prevention Plan for Roofing ($59)Sample documents
Free toolbox talks for your crew
Grinding Wheel Inspection and the Ring TestNail Gun Trigger Safety and RicochetUtility Knife Alternatives and TechniqueHand Tool Inspection and Mushroomed HeadsAll talks (EN/ES)